Programming Instructions for 2017 Chevrolet Bolt Remote Fob
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:A.
Programming with Two Working Smart Keys:
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner's manual. Up to 8 smart keys can be programmed to a vehicle.
1. Remove the emergency key blade from one of the working smart keys.
2. Place the two working smart keys in the cupholder.
3. Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock)
The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
4. Place the new smart key into the transmitter pocket with the buttons facing the bottom of the vehicle (to locate the transmitter pocket, take the small tray out of the center console storage area or refer to the owner's manual for the location).
5. Press the ignition POWER button to start the engine. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
6. Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
7. To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold the ignition POWER button for approximately 12 seconds to exit programming mode.
B.
Programming without Two Working Smart Keys:
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete.
DIY programming is not available in Canada.
Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner's manual. Up to 8 smart keys can be programmed to a vehicle.
Please Note:
if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
Key Programming Information for 2017 Chevrolet Bolt
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:A.
Programming with Two Working Smart Keys:
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner's manual. Up to 8 smart keys can be programmed to a vehicle.
1. Remove the emergency key blade from one of the working smart keys.
2. Place the two working smart keys in the cupholder.
3. Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock)
The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
4. Place the new smart key into the transmitter pocket with the buttons facing the bottom of the vehicle (to locate the transmitter pocket, take the small tray out of the center console storage area or refer to the owner's manual for the location).
5. Press the ignition POWER button to start the engine. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
6. Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
7. To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold the ignition POWER button for approximately 12 seconds to exit programming mode.
B.
Programming without Two Working Smart Keys:
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete.
DIY programming is not available in Canada.
Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner's manual. Up to 8 smart keys can be programmed to a vehicle.
Please Note:
if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
Use our Locksmith Search if you need professional help.